How to Repair a Furnace Flue

If you notice your home is not heating properly, or your heating bill has recently increased, you may need to examine your furnace and flue. Your furnace’s exhaust stack, also known as the flue, vents fumes and carbon monoxide safely away from your home’s interior as you heat your home. Over time, the galvanized metal will rust and corrode. If you notice rust forming, this could be a sign that you need to replace your furnace flue. If left untreated, you can risk leaking smoke and dangerous gases into your home.

Replacing a flue is a complicated process that should only be attempted by an experienced handy worker. A mistake during the replacement process could result in toxic gases entering in your home’s interior. Modernize recommends using a licensed professional for the most critical and large-scale home improvement projects. However, if you are confident in your skill set, here is how to replace your furnace flue.

furnace repair

How to Tell If Your Flue Needs to Be Replaced

Rust and leaks are the most obvious sign of flue repairs, but it’s important to note that not all corrosion is immediately visible from the ground. Your exhaust stack extends above your roofline, and there may be damage that you can’t detect.

Flues benefit from an annual cleaning and inspection. During this yearly cleaning, a professional can alert you to problems. You should also inspect your flue prior to moving into a new home, or installing a new furnace. You can also perform a visual inspection yourself. (It’s important to follow best practices and safety measures when climbing on your roof.) In addition to normal wear and corrosion, flues can be impacted by weather, bird’s nests, and debris.

Examine the entire length of the vent. Pay particularly close attention to the seals around the rain cap (the rounded part on the top of the vent) and the storm collar (a round bulging piece that fits just above the roof). Look for damaged pipes, cracking, and rust.

Before You Begin Your Flue Replacement:

Before you begin replacing your flue, turn off your furnace so it stops producing gases and toxic fumes.

Materials You Will Need:

  • Work gloves
  • Ladder
  • Tape measure
  • Pliers
  • Snips
  • A cordless drill
  • Galvanized sheet-metal ductwork
  • Galvanized steel elbows
  • Sheet-metal screws
  • High-temperature silicon or flue glue
  • Caulk gun
  • Pipe crimping device

Heating Pipes

Removing the Old Flue

Unscrew each connection and pull the damaged piece out. Use a soft cloth to gently clean around the edges of the flue.

Cut a New Piece to Length

Use a tape measure to get the length of the old piece. Then use your snips to cut a matching length of flue pipe. Crimp one end of the pipe using the pipe crimper to smooth it down.

Push the Pipe into Place

Next, take the length of cut pipe and push it into place so that it lines up with the connections. Push the connections from the existing exhaust pipe over the pipe. Next, take your drill and secure the pipe into place at the connection points using three to four sheet metal screws.

Caulk Over the Connection

Using high-heat silicone caulk, completely seal the joint by squeezing the caulk out in a neat bead and then smoothing it over. This will keep gases from escaping when you run your furnace, so it’s important to completely seal the joint so that no exhaust is let out. Wait until the caulk has dried fully before turning on your furnace again.

If You Need A Contractor

After your project, if you notice that your furnace still isn’t working well, have a professional examine your flue and furnace. Additionally, if you begin this DIY, and realize you need assistance, don’t hesitate to call an HVAC professional. An experienced contractor can assist with your flue replacement and see if the corrosion has led to other issues.

The post How to Repair a Furnace Flue appeared first on Modernize.

Modernize

BEST DEAL UPDATE:

Apple launches repair program for iPhone X units with faulty displays

iPhone X

Though not a widespread problem by any means, some iPhone X users over the past few months have experienced issues with non-responsive and temperamental displays. In light of this, Apple today launched a new replacement program for iPhone X users who have encountered this particular touch issue.

Per an Apple support document, impacted devices tend to exhibit one or two behaviors. Specifically, impacted iPhone X units will either not respond to touch at all or will react even when not touched. Either way, it’s undoubtedly a frustrating usability issue, especially for a device that was priced in excess of $ 999.

Continue reading…

BGR Top Deals:

  1. Behold: This is the Instant Pot of air fryers
  2. Today’s best deals: Instant Pot Duo60, $ 16 Bluetooth earbuds, $ 20 fast wireless charger, Dyson, more

Trending Right Now:

  1. This is what a sunrise on Mars sounds like, according to a computer algorithm
  2. Google just told us how to fix the worst thing about Androids and iPhones
  3. Black Friday 2018 deals from Microsoft: Deep discounts on Xbox, Surface laptops and tablets, more

Apple launches repair program for iPhone X units with faulty displays originally appeared on BGR.com on Sat, 10 Nov 2018 at 20:10:50 EDT. Please see our terms for use of feeds.


BGR

BEST DEAL UPDATE:

All Deals on HP, Dell and Lenovo!